esta aplicación esta diseñada como herramienta de aprendizaje y
análisis de señales de baja frecuencia en tiempo real con recursos
que se cuentan a mano como es un dispositivo móvil android un
modulo bluetooth un micro controlador y cualquier otro sensor
análogo al que se desee analizar; es el siguiente link se podrá
descargar el código necesario para la lectura de un sensor análogo
en este caso el código esta diseñado para leer la señal de
variación de un potenciometro sin embargo esta puede adaptarse de
manera simple para cualquier sensor análogo.
link_code_arduino:
https://drive.google.com/file/d/1iP56tn3kHmSXgYK750USVqkTRLz2t9sq/view?usp=sharing
Precaución.
si se escoge un tiempo de muestreo muy pequeño puede que tu dispositivo móvil no lo soporte y este reinicie la aplicación se sugiere empezar por tiempos de muestreo un poco mayores a los 200 mili segundos y luego ir reduciendo hasta encontrar el punto optimo de operación.
esta aplicación no reemplaza por completo la función de un osciloscopio ya que tiene sus limitaciones siendo el voltaje de entrada del micro-controlador de 0 a 5 voltios y la frecuencia de muestreo varia según el dispositivo.
aplicación realizada por Jose hidalgo.
This application is designed as a learning tool and analysis of low frequency signals in real time with resources that are available at hand such as an android mobile device a bluetooth module a micro controller and any other analog sensor that you want to analyze ; it is the following link the code necessary for reading an analog sensor can be downloaded in this case the code is designed to read the variation signal of a potentiometer however it can be adapted simply for any analog sensor.
link_code_arduino:
https://drive.google.com/file/d/1iP56tn3kHmSXgYK750USVqkTRLz2t9sq/view?usp=sharing
Caution.
If a very small sampling time is chosen your mobile device may not support it and restart the application it is suggested to start with sampling times a little greater than 200 milli seconds and then reduce until you find the optimal point of operation.
This application does not completely replace the function of an oscilloscope as it has its limitations the microcontroller input voltage being 0 to 5 volts and the sampling frequency varies depending on the device.
application made by Jose Hidalgo.
link_code_arduino:
https://drive.google.com/file/d/1iP56tn3kHmSXgYK750USVqkTRLz2t9sq/view?usp=sharing
Precaución.
si se escoge un tiempo de muestreo muy pequeño puede que tu dispositivo móvil no lo soporte y este reinicie la aplicación se sugiere empezar por tiempos de muestreo un poco mayores a los 200 mili segundos y luego ir reduciendo hasta encontrar el punto optimo de operación.
esta aplicación no reemplaza por completo la función de un osciloscopio ya que tiene sus limitaciones siendo el voltaje de entrada del micro-controlador de 0 a 5 voltios y la frecuencia de muestreo varia según el dispositivo.
aplicación realizada por Jose hidalgo.
This application is designed as a learning tool and analysis of low frequency signals in real time with resources that are available at hand such as an android mobile device a bluetooth module a micro controller and any other analog sensor that you want to analyze ; it is the following link the code necessary for reading an analog sensor can be downloaded in this case the code is designed to read the variation signal of a potentiometer however it can be adapted simply for any analog sensor.
link_code_arduino:
https://drive.google.com/file/d/1iP56tn3kHmSXgYK750USVqkTRLz2t9sq/view?usp=sharing
Caution.
If a very small sampling time is chosen your mobile device may not support it and restart the application it is suggested to start with sampling times a little greater than 200 milli seconds and then reduce until you find the optimal point of operation.
This application does not completely replace the function of an oscilloscope as it has its limitations the microcontroller input voltage being 0 to 5 volts and the sampling frequency varies depending on the device.
application made by Jose Hidalgo.
Show More >